Do I Have To Clean Brine Tank For My Water Softener

Video Transcript

Gary The H2o Guy:
Hi. I'grand Gary the Water Guy, and I own The Water Filter eStore and The Water Shop in Midland, Ontario.

Gary The Water Guy:
After you've had your water softener for a few years, yous may notice inside the brine tank that in that location'south a black ring and there'due south another blackness stuff along the sides. Aye. That's mold. We can see the mold stains around the exterior and the black ring, and that's what we want to get rid of. It's a practiced idea to remove that, to clean that out, so you get a nice, fresh start.

Gary The Water Guy:
Now, at that place'south a couple of different kinds of water softeners. At that place's a postal service-fill water softer like this Clack valve here, which means there's h2o in with the salt to make the brine, or there's a pre-fill water softener. If you see, there'south no h2o in with the salt. That means it's a pre-make full. Those ones are a niggling bit easier to clean out. Basically, yous only remove the salt, you lot clean within the brine tank. You tin utilize dish-washing soap. Or if the mold stains are quite significant, you tin can apply something like this, The Ultimate Mold Eliminator. And so yous refill it with table salt and you're good to go. With a mail service-fill one like this, yous have to remove the water commencement. You can either use a shop vac, or if yous want to do it a little bit easier and eliminate the step of the shop vac, you can actually put it into a regen bike. With the brine wheel, it'll depict the water out of the unit itself, and that'll make it a piffling bit easier.

Gary The Water Guy:
We tin can put this water softener into regen style just by belongings down the regen push button for 5 seconds. The first stage that it goes into is the backwash bicycle. Once information technology starts counting down, once the cycle'due south actually begun the timing, then we tin advance to the next cycle. Nosotros press the button again, we go into the brine cycle, and again, once it starts counting down, information technology's going to suck all the water out of the brine tank and it makes it a lot easier to make clean. Similar I say, either you tin can practise information technology this way, or it can use the shop vac. So when yous're done, when it's gone through the wheel, you can advance information technology through the rest of the cycles. Over again, once it starts counting downwardly, that's when you can advance it to the next one. And then take it back to abode. But for this particular procedure, we want to make sure we leave it on that brine cycle for the full 60 minutes. That way, it'll depict all the h2o out and make it a lot easier to clean out the brine tank.

Gary The H2o Guy:
Once y'all've done that, once more, you need to clean it out, put new salt. With the post-make full ones, you're going to take to add three gallons of water, set it to regenerate that night, and it'll go through the whole process, clean itself, and y'all'll exist back a hundred percent in service again the next day.

Gary The Water Guy:
Our newly cleaned alkali tank topped upwardly with salt and water. If yous like what y'all saw today, please click the subscribe button. That way, you'll be notified near whatsoever new videos that go available on this channel. If you want to become some more than information, you tin can go to our website, either thewaterstoremidland.com or thewaterfilterestore.com.

Again, I'm Gary the Water Guy from The H2o Store in Midland, Ontario. Thanks for watching.

If you've endemic your water softener for a few years or more you may notice some dark stains near the water line in the brine (table salt) tank. You guessed it,that's mold. Information technology's a good idea to clean that out so your h2o softener has a overnice, fresh start.

Mold Inside Water Softener Brine Tank

Cleaning out your alkali tank is a fairly piece of cake process, especially if y'all have a ii-piece h2o softener with a Clack valve like this one! Information technology should be done any fourth dimension you start to see night mold spots building up on the inside of your brine tank.

Start by planning alee. Yous volition desire to schedule this task for when you have a minimal amount of salt in the tank. If you're about to add together common salt to your brine tank and you notice these blackness lines, consider setting that salt bated and tackling a dainty cleanup get-go! And y'all definitely don't want to try this when you accept a salt clog!! If yous find yourself stuck with a table salt clog, take care of that first before trying to tackle the cleaning task.

Cleaning Pre-Fill vs Postal service-Fill Brine Tanks

Water Softener Salt Tablets

Most water softeners make full the brine tank with water as the last cycle of the Regeneration process, if that is the case with yours, yous will see water in the bottom of the alkali tank, intermixed with the softener salt. That is known as a Mail-Fill water softener. If y'all don't see any water in the lesser of your alkali tank, yours is a "Pre-Fill" water softener, which is the easiest to clean.For a Pre-Fill up water softener, all you lot need to practise is remove the salt, make clean the inside of the alkali tank, and then return the salt.

For a "Post Fill up" softener, which fills the brink tank after each regeneration wheel, y'all're going to need a few additional steps to remove the water AND the common salt from the alkali tank before y'all can make clean it properly.

Steps to Clean Your Alkali Tank

Cleaning Your Water Softener Brine Tank

Step 1 – Remove the Water from the Brine Tank

The first step is to remove the water from the alkali tank. Y'all can do this by using a moisture/dry Store Vac, or you tin allow the water softener do that for you lot.

To remove the brine in a "Mail service Fill" h2o softener with a Clack valve, start by forcing your h2o softener into a regeneration. On modernistic water softeners, this is hands done by holding down the regen button until the motor starts upward.

You lot want to go your water softener into the alkali bicycle then information technology starts to suck out the water in the brine tank, which is the 2nd bike so press the Regen button once more and the give-and-take Brine will announced on the brandish. You may demand to expect until the first cycle starts to count downwards before being able to printing the Regen button over again to skip this cycle.

Note the countdown time on the display, as that is usually an indication of how much time you have so that you lot tin can become and do something else while the alkali is beingness removed from the brine tank.

Once the h2o is out of the brine tank, place the water softener into featherbed and then the system doesn't refill the brine tank before you're finished.

Pace 2 – Remove the Salt from the Brine Tank

Once all the water is gone from the brine tank, y'all'll too want to get the remaining salt (if any) out of the way and so you can requite your brine tank a thorough cleaning.

You should be able to scoop the salt out of the brine tank and place it in a plastic saucepan. Merely make sure to article of clothing rubber gloves while doing this, as the pure salt tablets can be quite harsh on the skin.

Step 3 – Cleaning the Brine Tank

If you lot take a ii-piece h2o softener, you can either make clean the brine tank in place or disconnect it and take it outside where it might exist easier to make clean. With a jumpsuit water softener, you accept no choice simply to clean it in place. You can employ dishwashing soap to launder clean it out, or – if the mold is quite significant – you may need a mold eliminator. Once the alkali tank is spic and span, make sure to rinse information technology thoroughly to remove any soap residuum.

Remove the cleaning water by either dumping it out or with a store vac. Do NOT use the regen cycle to try to suck the h2o out of the brine tank again, as y'all don't want that water inbound your softener system.

Pace 4 – Filling and Restarting Your System

If you accept disconnected your alkali tank, outset by reconnecting information technology to the organization. Then you'll want to add a couple of new bags of table salt. Nosotros don't usually recommend putting the old salt dorsum into the softener, considering you want everything to have a nice, clean, fresh kickoff.

Add 3 gallons of water to the table salt and then manually scroll through the Regen cycles to get information technology back into service, if not already there. Take water softener out of featherbed and put information technology back into service.

Set up your system to "Regen Today" so the h2o softener volition Regen at its pre-set Regen time and it will go through the whole process, clean itself, and make certain you are back at 100% softening chapters past the next day.

Your Brine Tank is Clean, Fresh and Ready to Soften Your H2o

Clean Water Softener Brine Tank

Nobody likes dirty water, specially inside their home. Make sure to inspect the inside of your brine tank each time you add table salt to check for tell-tale signs of mold. If yous see them, clean them out to make certain your system is running at its best.

Let's Fix Your Water